HR824 mk2 Powered Studio Monitor with 8" Woofer (single)

$799.99

ZERO-EDGE BAFFLE™

The one-piece cast aluminum Zero Edge Baffle™ features precisely engineered curvature that minimizes diffraction for a crystal clear image of your mix, and effectively controls sound waves so you get detailed lows, full, articulate mids, and shimmering highs.

PRECISION AMPLIFICATION

The HRmk2 Series monitors contain separate onboard amplifiers for each driver, plus onboard active crossovers and time-correction circuitry, which helps ensure highs and lows reach your ears at the same time. The HRmk2s also have protection circuitry built in to protect from damaging input levels. 

UNPARALLELED QUALITY

We go to elaborate lengths to ensure each HRmk2 sounds as good as our experts intended. Each one we manufacture is subject to rigorous testing and pre-screening during the production process, then calibrated and tuned with an environmentally controlled test chamber before final packaging.

ROTATABLE LOGO

Due to their ultra-wide sweet zone, our HRmk2 monitors can be oriented vertically or horizontally, so we made our Mackie logo rotate-able. No matter which way you orient your HRmk2s, they’re always right-side up!

PASSIVE RADIATOR

The passive radiator replaces the port found on most speaker systems. One primary advantage of a passive radiator is that it can reproduce low frequencies with lower distortion and at a higher sound pressure level (SPL) than a simple port or duct.

CABINET DESIGN

The HRmk2 monitors feature a wood cabinet, with custom internal bracing to increase its strength and rigidity in desired locations. To absorb internal reflections and dampen standing waves inside the cabinet, an open-cell adiabatic foam material is placed strategically inside the box.

POWER AND OVERLOAD LED

Our LED power indicator is a tasty shade of white and red for when things get pushed a little too hard. We took care to make sure the brightness is just right, too. The light shines bright enough so you can see it just fine in a well-lit room, and in a dark environment, it won’t distract or blind you.

Materials and Construction:

3⁄4-inch (19 mm) thick MDF cabinet construction with internal bracing to add to cabinet stiffness. Piano-black gloss finish. Die-cast aluminum exponential wave guide for controlled, wide dispersion from high-frequency driver and Zero Edge Baffle™ to minimize diffraction around the cabinet edges. Open cell adiabatic “foam fill” acoustical damping material absorbs internal reflections, preventing delayed sound coloration. Flush-mount connector system allows monitor to be placed against a wall without need for connector clearance.

Low-frequency driver: Diameter:

8.75 inches (222mm) Sensitivity (2.83V, 1 m): 91 dB SPL Nominal Impedance: 4 ohms Voice Coil Diameter: 1.6 inches (40 mm) Frame: Die-cast magnesium Magnet: Ferrite Fully shielded: Ferrite opposing magnet High-frequency driver: Sensitivity (2.83V, 1m): 91 dB SPL Nominal Impedance: 6 ! Power Handling (Long Term/Program): 20/50 watts Frequency Range: 1.6 kHz to 22 kHz Diaphragm/Suspension: Titanium with polymer suspension Voice Coil Diameter: 1.0 inch (25.4 mm) Magnet: Neodymium Bucking Magnet: Ferrite opposing magnet Passive Radiator: 6-inch x 12-inch (152mm x 305mm) mass-loaded elliptical flat piston with variable thickness filleted edge rubber surround

Crossover Type:

Modified Linkwitz-Riley, 24 dB/octave @ 1900 Hz

Low-frequency power amplifier

Rated Power (at 1 kHz with 1% THD): 150 watts Rated Load Impedance: 4 ohms Burst Power Output: 350 watts Rated THD (1W to –1 dB of rated power): 0.1 % Slew Rate: 35V/µS Distortion (THD, SMPTE IMD, DIM 100): < 0.035% Signal-to-Noise (20Hz-20kHz, unweighted, referenced to 150W into 4!): > 102 dB Cooling: Convection Design: Class AB, Parametric Servo Feedback High-frequency power amplifier Rated Power(at 1 kHz with 1% THD): 100 watts Rated Load Impedance: 6 ohms Burst Power Output: 210 watts Rated THD (1W to –1 dB of rated power): 0.1 % Slew Rate: 35V/µS Distortion (THD, SMPTE IMD, DIM 100): < 0.035% Signal-to-Noise (20 Hz-20 kHz, unweighted, referenced to 100 W into 6 ohms): > 102 dB Cooling: Convection Design: Conventional Class AB

Input Type: Balanced Differential (XLR and 1/4" TRS) Unbalanced (RCA) Input Impedance: 20 k! Balanced 10 k! Unbalanced Input Protection: RFI and Level Protected Maximum Input Level: +20 dBu Low Frequency Filter: –3 dB @ 37 Hz, 2nd-order transitional high-pass filter –3 dB @ 47 Hz, 4th-order Chebyshev high-pass filter –3 dB @ 80 Hz, 4th-order Butterworth high-pass filter HF Equalization: ±2 dB @ 10 kHz, shelving Acoustic Space: A position: –4 dB @ 50 Hz, shelving B position: –2 dB @ 50 Hz, shelving C position: Flat Compressor: Independent high and low frequency overload detection Low Line Voltage Shut Down: 60% of Nominal Line Thermal Protection: Amplifier Shut-Down, Auto Reset Muting: 5 seconds at turn-on Driver Protection: Independent LF and HF Detection Overall Compression

Related products

View all
Patchwerks Gift Card
Patchwerks Gift Card
From $10.00
Patchwerks T Shirt
Doepfer A-111-6 Synthesizer Voice
Elektron Digitone 8 voice polyphonic digital synthesizer
Left Continue shopping
Your Order

You have no items in your cart